AC Ducting & Duct Installation
Duct Fabrication in Mirdif, Al Warqa & Al Mizhar
Duct Fabrication in Mirdif by The MELLS. Duct sections, bends, reducers and plenum boxes are cut and formed to site measurements, from galvanised sheet or pre insulated panel, then labelled for each run. We visit the property first and confirm the scope in a written quotation.
- Quotation
- Written, after a visit
- Response
- 2 hours in Dubai
- Quality checks
- 14 on every job
- Service
- Gold rated
5.0 on GoogleFully insuredNo subcontractorsOpen 08:00 to 19:00, Monday to Saturday
Duct Fabrication at a glance
| Service | Duct Fabrication |
|---|---|
| Location | Mirdif, Al Warqa & Al Mizhar, Dubai |
| Property types | Villas |
| Quotation | In writing, after a site visit and before any work begins |
| Typical duration | One to three days for most villas and fit out units |
| Team | Crew directly employed by The MELLS, with a named supervisor |
| Quality check | A measured test for every job, with photographs before and after |
| If a check fails | It is put right free of charge within 48 hours |
| Response | Two hours in Dubai for urgent work, planned work within 48 hours |
| Hours | 08:00 to 19:00, Monday to Saturday |
| Booking | Book a site visit on this page, call +971 55 444 0084 or email contact@themells.ae |
What is included
AC ducting sized, fabricated and installed for villas, apartments, offices, shops and restaurants, with joints sealed, ducts insulated and airflow balanced. A ducted AC is only as good as the ductwork hidden above the ceiling. Ducts that are too small are noisy and starve the far rooms, and in Dubai humidity any gap in the insulation sweats and drips onto the ceiling below. Our own technicians work out the airflow each room needs, then fabricate, hang, seal and insulate the ducts and balance the system before handover.
- Site measured and a cutting list drawn up for each run
- Sheet cut, folded and seamed, or panel grooved and glued
- Bends, reducers and take offs made to the measured angles
- Each piece labelled with its run and position before delivery
How we carry out duct fabrication
Fabrication begins with a tape measure in the ceiling void, not with a catalogue. Each run is drawn with its lengths, offsets and changes of size, and a cutting list is made from the drawing. Galvanised sheet is cut, folded and closed with a locked seam, and flanges are fitted to the ends. Pre insulated panel is cut with a grooving tool, folded into a box, then glued and taped along the seam. Bends are made with a generous radius or fitted with turning vanes so the air does not tumble.
Poor fabrication shows up as noise and lost airflow. A sharp square bend with no vanes, or a sudden step down in size, makes the duct rumble and whistle. Thin sheet on a wide duct drums every time the fan starts unless it is cross braced. In Dubai villas the voids are often shallow and crowded with beams, so off the shelf fittings rarely fit and the pieces have to be made to suit. The site visit measures every obstruction before anything is cut.
How it works
The same method on every job, so the result does not depend on who is on shift.
- Survey and diagnosis. A technician inspects the system or surface, takes readings and photographs, and explains what was found in plain language.
- Written quotation. You receive a written quotation against a defined scope before any work starts. Anything outside that scope is quoted separately.
- Protected, supervised work. The work area is protected and isolated, and the job is carried out by our own technicians under a named supervisor.
- Testing. Every job ends with a measured test suited to the discipline, so the result is a reading and a photograph and not an opinion.
- Report and warranty. The completed report reaches you within the hour. Any failed point is put right free of charge within 48 hours.
Duct Fabrication in Mirdif: what we plan for
Mirdif is one of Dubai's established family districts, east of the airport, with streets of private villas built from the 1990s onwards, the townhouses of Shorooq and Mushrif Village, and apartments at Uptown Mirdif, Ghoroob, Mirdif Hills and Mirdif Tulip. Al Warqa, Al Mizhar, Al Rashidiya, Nad Al Hamar and Al Khawaneej surround it with larger private villas.
Many homes here are twenty to thirty years old, so AC ducts, water tanks, roofs and bathrooms have had time to collect what newer communities have not seen yet. Mature gardens bring leaf litter and irrigation marks, and dust settles quickly on sills, roofs and outdoor furniture. In villas of this age the AC ducts, drain lines, water heaters, pumps and rooftop tanks are usually due for attention. We inspect first and report what is urgent and what can wait.
Most streets are open, with no community gate, and we park at the villa. Apartment communities such as Ghoroob, Uptown Mirdif and Mirdif Hills need a work permit from building management, which we arrange.
What your quotation depends on
A quotation for duct fabrication in Mirdif follows a site visit. The supervisor looks at the points listed here and you receive a written quotation with a defined scope before any work begins. Once you accept it, nothing is added on the day.
- Size and type of the system or surface
- Present condition and ease of access
- Parts and materials specified
- One visit or a retained contract
Related services in Mirdif
Each one has its own scope and method.
Duct Fabrication across Mirdif
Questions about duct fabrication in Mirdif
What does duct fabrication include?
Duct sections, bends, reducers and plenum boxes are cut and formed to site measurements, from galvanised sheet or pre insulated panel, then labelled for each run. The work includes site measured and a cutting list drawn up for each run; sheet cut, folded and seamed, or panel grooved and glued; bends, reducers and take offs made to the measured angles.
Can you make a duct piece to match an existing system?
We can. The existing duct, its flange type and the insulation thickness are measured, and the new section is made to join it. A single reducer, an offset round a beam or a new plenum box for a larger diffuser are all common requests.
What thickness of sheet do you use?
It depends on the width of the duct and the pressure the fan produces. Wider ducts need heavier sheet and stiffening so the sides do not drum. The gauge for each run is listed in the written quotation.
How much does duct fabrication cost in Mirdif?
We do not publish prices, because no two jobs are the same. The main factors: size and type of the system or surface; present condition and ease of access. Book a site visit: a supervisor from The MELLS looks at the work and you receive a written quotation with a defined scope before anything begins.
Who provides duct fabrication in Mirdif?
The MELLS provides duct fabrication in Mirdif, Dubai. The work is carried out by people The MELLS employs directly, under a named supervisor, 08:00 to 19:00, Monday to Saturday. To arrange it, book a site visit on this page or call +971 55 444 0084.
How long does duct fabrication take?
Typically one to three days for most villas and fit out units. The time for your property is confirmed with the quotation.
Why are some rooms colder than others?
The far rooms are usually short of air. The ducts may be undersized, a flexible duct may be crushed, or the branches may have no dampers. We measure the airflow at each outlet, correct the duct and balance the system.
Which is better, galvanised steel or pre insulated duct?
Both work well when they are installed properly. Steel is stronger and suits long main runs, plant rooms and exposed ducts. Pre insulated panel is lighter and suits homes with shallow voids. We recommend one after seeing the site.
Does the building need to agree to duct changes?
In towers and malls, changes to the ducts, fire dampers or fresh air system are coordinated with building management. What the building asks for is identified at the site visit, and we prepare the paperwork.
How do your crews get access to Mirdif?
Most streets are open, with no community gate, and we park at the villa. Apartment communities such as Ghoroob, Uptown Mirdif and Mirdif Hills need a work permit from building management, which we arrange.
Do you work in older villas in Mirdif?
Yes. Much of our work in Mirdif, Al Warqa and Al Mizhar is in villas twenty years old or more, where the supervisor checks ducts, tanks, roofs and bathrooms at the site visit and writes what was found into the quotation.
How do I choose a company for duct fabrication in Mirdif?
Ask four things: who employs the people who will come, whether the scope is written down before work starts, how the result is checked, and what happens if something is missed. The MELLS uses its own staff, quotes in writing after a site visit, checks every job (a measured test for every job, with photographs before and after) and puts right any failed check free of charge within 48 hours.
Can you come to Mirdif at short notice?
Yes. Crews travel from our Barsha Heights base, and urgent work in Dubai is attended within two hours between 08:00 and 19:00, Monday to Saturday.
Page updated by The MELLS, Damac Executive Heights, Barsha Heights, Dubai.