AC Ducting & Duct Installation
Duct Fabrication in Sheikh Zayed Road, Trade Centre & Zabeel
The MELLS provides duct fabrication in Sheikh Zayed Road with its own directly employed team. Duct sections, bends, reducers and plenum boxes are cut and formed to site measurements, from galvanised sheet or pre insulated panel, then labelled for each run. We visit the property first and confirm the scope in a written quotation.
- Quotation
- Written, after a visit
- Response
- 2 hours in Dubai
- Quality checks
- 14 on every job
- Service
- Gold rated
5.0 on GoogleFully insuredNo subcontractorsOpen 08:00 to 19:00, Monday to Saturday
Duct Fabrication at a glance
| Service | Duct Fabrication |
|---|---|
| Location | Sheikh Zayed Road, Trade Centre & Zabeel, Dubai |
| Property types | Apartments |
| Quotation | In writing, after a site visit and before any work begins |
| Typical duration | One to three days for most villas and fit out units |
| Team | Crew directly employed by The MELLS, with a named supervisor |
| Quality check | A measured test for every job, with photographs before and after |
| If a check fails | It is put right free of charge within 48 hours |
| Response | Two hours in Dubai for urgent work, planned work within 48 hours |
| Hours | 08:00 to 19:00, Monday to Saturday |
| Booking | Book a site visit on this page, call +971 55 444 0084 or email contact@themells.ae |
What is included
AC ducting sized, fabricated and installed for villas, apartments, offices, shops and restaurants, with joints sealed, ducts insulated and airflow balanced. A ducted AC is only as good as the ductwork hidden above the ceiling. Ducts that are too small are noisy and starve the far rooms, and in Dubai humidity any gap in the insulation sweats and drips onto the ceiling below. Our own technicians work out the airflow each room needs, then fabricate, hang, seal and insulate the ducts and balance the system before handover.
- Site measured and a cutting list drawn up for each run
- Sheet cut, folded and seamed, or panel grooved and glued
- Bends, reducers and take offs made to the measured angles
- Each piece labelled with its run and position before delivery
How we carry out duct fabrication
Fabrication begins with a tape measure in the ceiling void, not with a catalogue. Each run is drawn with its lengths, offsets and changes of size, and a cutting list is made from the drawing. Galvanised sheet is cut, folded and closed with a locked seam, and flanges are fitted to the ends. Pre insulated panel is cut with a grooving tool, folded into a box, then glued and taped along the seam. Bends are made with a generous radius or fitted with turning vanes so the air does not tumble.
Poor fabrication shows up as noise and lost airflow. A sharp square bend with no vanes, or a sudden step down in size, makes the duct rumble and whistle. Thin sheet on a wide duct drums every time the fan starts unless it is cross braced. In Dubai villas the voids are often shallow and crowded with beams, so off the shelf fittings rarely fit and the pieces have to be made to suit. The site visit measures every obstruction before anything is cut.
How it works
The same method on every job, so the result does not depend on who is on shift.
- Survey and diagnosis. A technician inspects the system or surface, takes readings and photographs, and explains what was found in plain language.
- Written quotation. You receive a written quotation against a defined scope before any work starts. Anything outside that scope is quoted separately.
- Protected, supervised work. The work area is protected and isolated, and the job is carried out by our own technicians under a named supervisor.
- Testing. Every job ends with a measured test suited to the discipline, so the result is a reading and a photograph and not an opinion.
- Report and warranty. The completed report reaches you within the hour. Any failed point is put right free of charge within 48 hours.
Duct Fabrication in Sheikh Zayed Road: what we plan for
This is the original tower strip of Dubai. Residential, hotel and office towers line both sides of Sheikh Zayed Road between the Trade Centre roundabout and Downtown, among them Emirates Towers, 21st Century Tower, Sama Tower, Park Place Tower and Latifa Tower. Dubai World Trade Centre and One Central form the exhibition and office quarter at the northern end. Behind the towers lie the low rise streets of Al Satwa, the villas of Zabeel and the newer apartment buildings of Wasl 1.
Sheikh Zayed Road carries traffic through every working hour, and its exhaust film coats road facing glass, balcony floors and window sills. It is greasy, so plain water smears it. The same particles are drawn into fresh air intakes and AC filters. Higher floors get less grit but more windblown dust in the door tracks. Fresh air intakes and filters load quickly beside the road. Fan coil units and older ducted systems have filters, coils, trays and drain lines cleaned, and a ceiling stain is traced to the leaking drain before any repainting.
Every tower has a management office that issues work permits, checks staff details and books the service lift. The MELLS submits those requests. Loading is from the service road behind the towers, never from Sheikh Zayed Road itself. Villas in Zabeel and Al Satwa are on open streets.
What your quotation depends on
A quotation for duct fabrication in Sheikh Zayed Road follows a site visit. The supervisor looks at the points listed here and you receive a written quotation with a defined scope before any work begins. Once you accept it, nothing is added on the day.
- Size and type of the system or surface
- Present condition and ease of access
- Parts and materials specified
- One visit or a retained contract
Related services in Sheikh Zayed Road
Each one has its own scope and method.
Duct Fabrication across Sheikh Zayed Road
Questions about duct fabrication in Sheikh Zayed Road
What does duct fabrication include?
Duct sections, bends, reducers and plenum boxes are cut and formed to site measurements, from galvanised sheet or pre insulated panel, then labelled for each run. The work includes site measured and a cutting list drawn up for each run; sheet cut, folded and seamed, or panel grooved and glued; bends, reducers and take offs made to the measured angles.
Can you make a duct piece to match an existing system?
We can. The existing duct, its flange type and the insulation thickness are measured, and the new section is made to join it. A single reducer, an offset round a beam or a new plenum box for a larger diffuser are all common requests.
What thickness of sheet do you use?
It depends on the width of the duct and the pressure the fan produces. Wider ducts need heavier sheet and stiffening so the sides do not drum. The gauge for each run is listed in the written quotation.
How much does duct fabrication cost in Sheikh Zayed Road?
We do not publish prices, because no two jobs are the same. The main factors: size and type of the system or surface; present condition and ease of access. Book a site visit: a supervisor from The MELLS looks at the work and you receive a written quotation with a defined scope before anything begins.
Who provides duct fabrication in Sheikh Zayed Road?
The MELLS provides duct fabrication in Sheikh Zayed Road, Dubai. The work is carried out by people The MELLS employs directly, under a named supervisor, 08:00 to 19:00, Monday to Saturday. To arrange it, book a site visit on this page or call +971 55 444 0084.
How long does duct fabrication take?
Typically one to three days for most villas and fit out units. The time for your property is confirmed with the quotation.
Does the building need to agree to duct changes?
In towers and malls, changes to the ducts, fire dampers or fresh air system are coordinated with building management. What the building asks for is identified at the site visit, and we prepare the paperwork.
Does the ceiling have to come down?
Not always. Tile ceilings lift out and go back. In a gypsum ceiling we cut openings where the work is and close them afterwards, leaving access panels under the unit and at the dampers.
Do you install AC ducting in Sheikh Zayed Road?
Yes. We install, replace and alter AC ducting in villas, apartments, offices, shops and restaurants across Dubai. A site visit measures the ceiling void and the AC unit before the scope is put in writing.
Do you arrange the building permit in Sheikh Zayed Road?
Yes. Most buildings ask contractors for a work permit, trade licence, insurance and staff IDs, and a service lift booking. We submit all of it for you.
Do you work in the towers on both sides of Sheikh Zayed Road?
Yes. Apartments and offices on both sides are covered, from the Trade Centre end down towards Downtown. The permit and the lift booking are requested from the tower before the crew is confirmed.
How do I choose a company for duct fabrication in Sheikh Zayed Road?
Ask four things: who employs the people who will come, whether the scope is written down before work starts, how the result is checked, and what happens if something is missed. The MELLS uses its own staff, quotes in writing after a site visit, checks every job (a measured test for every job, with photographs before and after) and puts right any failed check free of charge within 48 hours.
Can you come to Sheikh Zayed Road at short notice?
Yes. Crews travel from our Barsha Heights base, and urgent work in Dubai is attended within two hours between 08:00 and 19:00, Monday to Saturday.
Page updated by The MELLS, Damac Executive Heights, Barsha Heights, Dubai.